Stabilization Network×ウェーブクレスト - List of Manufacturers, Suppliers, Companies and Products

Stabilization Network Product List

1～3 item / All 3 items

Displayed results
Power supply impedance stabilization circuit network 50Ω/50μH+5Ω, 8A

Power supply impedance stabilization circuit network 50Ω/50μH+5Ω, 8A

Line Impedance Stabilization Network for measuring line-conducted interference in the range of 9 kHz to 30 MHz in accordance with CISPR 16 standards.

【Product Overview】 The TBLC08 50μH LISN is a line impedance stabilization network designed to measure line-conducted interference in the frequency range of 9kHz to 30MHz, in accordance with the CISPR16 standard. This device is designed to test single-phase AC power supplies with a maximum supply voltage of 240V. Conducted noise can be measured on both the phase and neutral lines. The TBLC08 features a switchable limiter/attenuator and an artificial hand connection. This device is available with country-specific DUT connectors.

  • Measurement and analysis equipment leasing and rental

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
50Ω/50μH+5Ω, 16A power supply impedance stabilization circuit network

50Ω/50μH+5Ω, 16A power supply impedance stabilization circuit network

Line impedance stabilization network for measuring line-conducted interference in accordance with CISPR 16-1-2 standards.

**Product Overview** The TBL5016-2 is a line impedance stabilization network designed to measure conducted interference in the range of 9kHz to 30MHz, in accordance with the CISPR 16-1-2 standard. This device is designed to test single-phase AC power supplies with a maximum supply voltage of 240V and 16A. Conducted noise can be measured on both the phase and neutral lines. The TBL5016-2 is equipped with a switchable limiter/attenuator and an artificial manual connection. This device is available with country-specific DUT connectors.

  • Measurement and analysis equipment leasing and rental

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
5μH, 50A power supply impedance stabilization circuit network

5μH, 50A power supply impedance stabilization circuit network

Compliant with standards CISPR 16-1-2, CISPR 25, EN 55025, MIL-STD-461F.

**Product Overview** The TBL0550-1 5µH LISN is a device necessary for setting up conducted noise measurements of electronic equipment powered by DC sources. It is designed to comply with CISPR 16-1-2, CISPR-25, EN55025, MIL-STD-461F, and ISO11452-4, and is intended for measurements in the frequency range of 150kHz to 110MHz, with limited use of DO-160 / ED-14G and ISO7637-2. The LISN is inserted into the supply line of the DUT (Device Under Test). Conducted noise present at the power terminals of the DUT can be measured via a BNC connector using a spectrum analyzer or measurement receiver. The source (power) terminal and the DUT terminal are decoupled by a 5µH inductor. By combining two TBL0550-1 units with the Tekbox LISN Mate, common mode noise and differential mode noise can be measured separately. The unit is equipped with a BNC male-N-male RG232 cable, coupling connectors, and a ground bracket for connection to a ground plane.

  • Measurement and analysis equipment leasing and rental

Added to bookmarks

Bookmarks list

Bookmark has been removed

Bookmarks list

You can't add any more bookmarks

By registering as a member, you can increase the number of bookmarks you can save and organize them with labels.

Free membership registration
COPYRIGHT © 2001-2025 IPROS CORPORATION ALL RIGHTS RESERVED.